How to Tighten Loose Watch Hands – Step By Step Guide

If you’ve ever had this problem, you know how frustrating it can be. Some people have even had to replace their watches because of the damage done to their hands. However, there’s no reason you should have to put up with the same problem.

In this post, we’ll show you how to tighten loose your watch hands so you never have to worry about them again. There are a few different ways to draw a watch hand. The most common way is to use a screwdriver. 

How to fix loose watch hands? To put it simply, you’ll need to pull the spring. If your watch hands are loose, there are a few things you may do to tighten them up. Follow these methods to tighten them up:

How to Tighten Hour Hand on a Clock

I’ll show you how to tighten loose watch hour hand in this post. This is a very simple task that can be done in just a few minutes. The result will be much more precise.

Here, we’ll show you how to tighten loose watch hour hand.

Step 1: Push the hour hand

 There is a cover on the back of the watch; unscrew the back cap. Look at the movement. You will see the minute hand and the hour hand on the right-hand side. 

The first step is to push the hour hand back into place. This is done by pushing the needle down with your thumb. The second step is to rotate the watch, so the hour hand points at 3 o’clock.

The third step is to pull the minute hand towards you. This is done by wrapping your fingers around the minute hand and slowly pulling it towards you.

Step 2: Tighten the tiny nut

Next, you’ll need to tighten the tiny nut that holds the hour hand. This is done by pulling the screw. To do this, grab the screwdriver and tighten the screw. After drawing the screw, it is time to adjust the hour hand. Place your hand over the hour hand and rotate it towards the 12 o’clock position. Rotate it until it is in the desired position. 

Step 3: Check the timepiece

Once you’ve tightened the hour hand, it is time to check the timepiece. To do this, check the time on the watch. If it is off by a few seconds, you may need to adjust the minute hand. 

How to fix lose a minute hand

The minute hand of your watch or clock can get loose, resulting in it skipping or running fast. This can be a big problem if you have a timepiece that you rely on to tell the time but don’t have the time to take it to the watchmaker to have it fixed.

If your watch is running slow, there are a few things you can do to try and fix the issue. Here are a few ways you can tighten up you lose minute hand:

Step 1: Remove the straps

First, you’ll need to remove the two straps attached to the back of the panel. Grab the plastic in the back and pull it towards you to do this. Once you’ve pulled it out, hold the plastic and pull it up.

Next, you’ll need to remove the panels. To do this, pull up on the front of the forum and pull it out. Now, you’ll need to get a flathead screwdriver. You can use this to tighten the springs that hold your hands.

Step 2: Removing the cannon pinion

The cannon pinion must be removed once the straps and panel have been removed. To do so, grip the watch’s top and pull it up. After that, you must remove the cannon pinion.

To accomplish this, grab the top of the watch and pull it up. To access the cannon pinion, you’ll need a little screwdriver.

Step 3: Tightening the cannon pinion

Once you’ve removed the cannon pinion, you’ll need to tighten the cannon pinion. This is done by pulling down on the watch with your fingers. This will force the cannon pinion to tighten

1. Turn the watch, so the cannon pinion is facing up.

2. With the help of a flat head screwdriver, pry the cannon pinion of the gear wheel.

3. Hold the cannon pinion with one hand and tighten the pinion screw with the other hand.

YOU MAY READ THIS NEXT: What is The Dial on a Watch

How to Fix Clock Hands Stuck

You may find that your hands are stuck, and you can’t get them to move. This can be a big problem if you have a timepiece that you rely on to tell the time but don’t have the time to take it to the watchmaker to have it fixed.

Steps to fix the clock hands stuck

Step 1: Remove the back cover

You’ll need to start by removing the rear cover. To do so, grip the watch’s top and pull it up. Next, remove the four screws that keep the rear cover in place using a screwdriver.

Once the screws are removed, gently pull the back cover off of the watch. Now you’ll need to remove the battery. Gently pull the battery cover off of the watch. Remove the battery from the watch.

Step 2: Remove the Minute Hand

Now, you’ll need to remove the minute hand. To do this, gently pull the minute hand out of the watch. Once you have the minute handout, you will need to remove the hour hand.  

Step 3: Remove Hour Hand

To do this, gently pull the hour hand out of the watch. Once you have the hour handout, you’ll need to remove the gear train. To do this, use a screwdriver to remove the gear train.

Step 4: Tighten the Gear Train

Next, you’ll need to tighten the gear train. To do this, grab the gear train and pull it towards you. Be careful not to pull too hard on the gear train, or you may damage it.

 Once the gear train is tight, you can reinstall the cover. Ensure the surface is seated correctly on the gear train and tighten the screws.

Conclusion About How to Tighten Loose Watch Hands

In conclusion, watch hands are an essential part of any watch. But, they are also one of the most challenging parts of the watch to fix. And, if you don’t know how to do it, you can end up with a watch that is hard to read and even harder to use.

So this is what we’ll talk about in this article. We’ll show you how to loosen and tighten your watch hands with some amazing tips and tricks.

I hope you like and benefit from this essay. I also hope it aids you in learning how to repair your watch hands.

Please feel free to leave any questions or comments in the box below.